FieldFox Analyzer Firmware Archive (N991xA, N992xA, N993xA FieldFox models)

- SCPI command for FULL SCREEN
- QuickCal fails with 'ArgumentOutOfRangeException' using 1.5m cable and narrow span below 1MHz - Differential measurement impedance format calculation incorrect
- can't enter IP addresses in LanConfig screen
- Increase the offset value limit in pulse measurement mode --- -80 dB is not big enough - Mouse usage causes limit line crash
- S2p file saving" Error: NullReferenceException
- After resuming from suspend with battery saver OFF, bad data
- SRC unlock in USB power sensor mode when turning on source, N9912A
- Timeout during NA/CAT OSL with >= 4001 points
- ERTA/TSS CableWizard creates BAD cable files upon multiple use
- 85052C with full 2-port cal results in cal GUI with some progress bars hidden
- QuickCal broken after recent cal fix

- SCPI command for FULL SCREEN

- QuickCal fails with 'ArgumentOutOfRangeException' using 1.5m cable and narrow span below 1MHz

- OBD: If active mode in user preset .sta file is no longer licensed, unit will fail to boot

- Differential measurement impedance format calculation incorrect

- can't enter IP addresses in LanConfig screen

- Increase the offset value limit in pulse measurement mode --- -80 dB is not big enough

- Customer cannot recall N9912A file

- Mouse usage causes limit line crash

- After resuming from suspend with battery saver OFF, bad data

- SRC unlock in USB power sensor mode when turning on source, N9912A

- Fixed: SCPI state file will fail siliently when non-system menu is in the menu history.
- Fixed: QuickCal fails with 'ArgumentOutOfRangeException' when using 1.5m cable and narrow span below 1MHz.

- Fixed: QSOLT produces "invalid connector ID" errors when using Type N connectors with the T calkit selected.
- Fixed crash when autoscaling.
- Fixed Radio standards dial (knob) issue in SA Mode.
- Bug fixed for ERTA Connection Wizard.

- Support for U2043XA Wide Dynamic Range Average power sensor
- GPS dongle update due to obsolescence (N9912A and N9923A/AN Only).
- ERTA SCPI command update --> see programming guide.
- Option 330 bug fixes.

Other bugs fixes:
- Marker BW Q setting is lost when changing between the 2 Big Marker states (A & B).
- IP address allows entry of non-IP-address-compliant characters.
- Trigger level not following display change when external gain compensation applied.
- Setting GPSCoordinateDisplayFormat to None in preferences will cause unit to not start.
- Instruction text for Port 1 and Port 2 is backwards for isolation cal.
- N9912A QuickCal - Cable loss failure with measuring load step fails to report error and exit cal wizard.

- Add SCPI command for Local-Remote keyboard utility
- Marker target search enhancement
- Fix bug when captures from Data Link on missing number of averages in CAT/NA mode, and smoothing indicator in NA mode.

- Enabled 7-16 connector type Ecal module for calibration use.
- Fix bug on SCPI command for normalization (THRU 1,2).

- NA mode: Marker commands will crash when marker x value is too close to the end of the frequency span, and when also a marker search is performed.
- NA mode: Enable SCPI command for target search on specific direction (right or left direction search). Previously was set as looping only.

- Fix bug where VVM return zero value when recalling two different states.
- Fix bug where GPS display preferences is not active after unit reboot.
- Fix crash when spectrogram time marker is set more than 450.
- Fix bug on SA mode when signal is not at the correct amplitude after resuming from suspend.
- Japanese language translation updates in FieldFox

- Support option 208, Frequency Offset with USB Power Sensor (FOPS)
- Support option 212, 1-Port mixed-mode S-parameters
- Add Velocity factor for CAT mode DTF waveguide measurements 
- Add Impedance Z and admittance Y parameter conversion
- Add 1-port response calibration w/isolation 
- Add memory trace for Pulse Measurements
- Add print to PCL USB printers
- Add Update time via internet
- Add SCPI support for CPM
- Add Portuguese language
- Fixed: Simple ECal ON ignored for type N ECal
- Fixed: Interference Rejection levels Minimum and Medium appear to be completely broken
- Fixed: Initialization hang if unit is talked to over LAN "too early" in the boot process

- Fixed: N9912 Normalization Cal issue.
- Fixed: N9912 Quick Cal issue with long cable
- Fixed: All models intermittently hang during startup when communicating over LAN

- Enhancements to response cal, both short response and normalization.
- .csv data saved in same format as display
- ECal and preset issues resolved

- Supports option 330, Pulse Measurements.
- Supports ECal on all models, except N9912A. ECal must be connected to FieldFox before performing calibration.

- Add support to install option licenses via external USB CD-ROM/DVD-ROM
- Add support to update new firmware revision via external USB CD-ROM/DVD-ROM

- Supports U8485A power sensor
- Fixed crash when using knob in "edit preferences" screen
- Fixed crash when switching from trace#1 to trace #2 with Smith Chart and Scaling.

- Enable "set time forward" with only one change per day.
- Fixed "checking for 430 upgrade" line.

- Supports remote control viewing on iOS devices and other bug fixes. Required Option 030 to control FieldFox remotely via iOS devices.

- Supports Spectrum Analyzer Time Gating capability, required Option 238. See configuration guide for ordering info.

- Various bugs fixes. Please refer to firmware release notes for more info.

• Implementation of time/date restriction setting on FieldFox. Please set local time correctly before updating from previous revision to A.07.xx.

N9912A, N9923A,
N9913A, N9914A, N9915A, N9916A, N9917A, N9918A,
N9925A, N9926A, N9927A, N9928A,
N9935A, N9936A, N9937A, N9938A

- Various bugs fixes. Please refer to firmware release notes for more info.

N9912A, N9923A,
N9913A, N9914A, N9915A, N9916A, N9917A, N9918A,
N9925A, N9926A, N9927A, N9928A,
N9935A, N9936A, N9937A, N9938A

- Fixed bug when inserting slow USB flash drive that will show error message "Please Reboot. Expected hardware not present"

N9912A, N9923A,
N9913A, N9914A, N9915A, N9916A, N9917A, N9918A,
N9925A, N9926A, N9927A, N9928A,
N9935A, N9936A, N9937A, N9938A

- Add Turkish and Russian language support.
- Compatible with DataLink version 4.12

N9913A, N9914A, N9915A, N9916A, N9917A, N9918A,
N9925A, N9926A, N9927A, N9928A,
N9935A, N9936A, N9937A, N9938A

N9912A, N9923A.

- Compatible with DataLink version 3.60 and above.

September 18, 2009 

September 1, 2009

N9912A

Zip file containing firmware files for MY serial numbers ONLY

N9912A

Zip file containing Firmware files for US/SG serial numbers ONLY